How to Disable HowToDisable
Related Articles
There are many ways to disable aftermarket car alarms. These include cutting the wires, resetting the alarm, and identifying the fuse. If you can’t find a fuse, you can try to rewire the whole system. This will require some technical knowledge. However, if you follow the correct procedure, you should be able to disable your alarm without any hassle.
Cut the wires
To disable an aftermarket car alarm, you must first cut the wires that are connected to the module. This module is often located in the engine bay or cabin. The two largest wires in the module splice into the ignition wire. You can use wire cutters to cut the wires. If you need to disable the negative circuit, you can use plastic tweezers.
To disable the alarm, you must first remove the module, which usually has two wires that are 12 or 14 gauge. You can splice them back together by unscrewing the spliced wires. You can also cut the wires to the parking light or door lock interface. Some alarms have a twisted wiring pattern, making it difficult to splice the wires back together.
Next, you must locate the battery of the vehicle. It is usually located under the hood, while some cars have the battery in the trunk. You will need to locate the negative terminal cable, which should be black and marked with a minus symbol. Remove the cable for about a minute, and then reconnect it. The alarm should be off after this time, but if you find the battery is dead, you may need to take the vehicle to a mechanic’s shop for repair.
Reset the alarm
The first step to resetting the aftermarket car alarm is to disconnect the battery from the vehicle. This will cut off the power to the car alarm and turn it off. Then, reconnect the negative terminal wire to your battery. This should reset all the electrical systems. If your car alarm still continues to flash, you may need to do more invasive steps.
Once the alarm is turned off, turn the ignition to the “On” position. A chirping sound will occur from the transmitter, which is usually located beneath the driver’s side of the dash near the ignition cylinder. If the alarm is triggered by the hood position sensor, you can disable it by closing the hood. If it is not, make sure to press the unlock button on the key fob.
If you’re not mechanically inclined, you can always try to reset the car alarm manually. Many aftermarket car alarms come with wires under the steering wheel. If you’re not confident in your ability to do this, seek the help of a technician. If you’re not confident with electronics, you may need to use a wire cutter.
Removing the main module
The first step in removing the main module of an aftermarket car alarm is to unplug the car alarm system. The module contains the wiring and sensors that trigger the alarm. These include the motion sensor, radar sensor, door lock plug, and antenna. After removing the module, you should be able to replace it with another aftermarket car alarm system.
The main module of the alarm system is located under the driver’s side of the dash, tucked behind the kick panel. It is usually zip-tied into place. The module comes with six or eight wires that connect it to various parts of the car.
Next, you need to locate the fuse box and vehicle wiring. Then, cut the power wire coming from the aftermarket car alarm. Make sure not to cut the wires that connect to the other wires. This will cause the alarm to stop working, so be careful. Remember to wear protective gear when working on the car. You should also read your car’s manual before performing any work on it.
Identifying the fuse
When it comes to how to disable aftermarket car alarm, identifying the fuse is crucial. Most modern vehicles have brightly colored plastic caps that cover the fuse box, so it’s not always easy to see it. If you need to disable an alarm quickly, you can cut the wires and remove the fuse yourself. However, you should only do this after you have followed proper safety precautions.
The fuse used for the factory alarm is separate from the fuse for the aftermarket ones. Identifying the fuse for the aftermarket car alarm should be easy if you have the owner’s manual for the car. The fuse box is generally located under the hood of the car. It may also come with pictures of the fuse box.
After identifying the fuse, you can now dismantle the aftermarket car alarm by cutting the wire and removing the alarm. You should carefully remove the cabin trim and protect your hands by wearing safety gloves. Then, cut the circuit with a pair of pliers or plastic tweezers.
